=================================================
Abaqus Datasets used in Papers
1) Robust and Fast Extraction of 3D Symmetric Tensor Field Topology (neu)
2) Mode Surfaces of Symmetric Tensor Fields: Topological Analysis and Seamless Extraction (mode)

------------------------------------------------

Each folder contains:
1) inp files: the mesh data from Abaqus
2) rpt files: the tensor field data from Abaqus
3) png files: the images used in the papers

=================================================
Setup and Dimension
=================================================
neu_01_SteelRod_CylinderCircularLong 
(Neu fig. 1 (a)&(b))
------------------------------------------------
1. Setup
a simulated cylindrical steel rod, with the bottom fixed and a tangential force applied on the top.

2. Dimension
   verts:672
   tets:480 * 6 = 2,880

=================================================
neu_02_TorusVertical0p1 
(Neu fig. 1 (c)&(d), fig. 11 (a)&(b))
------------------------------------------------
1. Setup
A torus (representing a tire) that has boundary conditions at the top and the bottom. When a tire is pressed to the ground during rolling, the top side of the tire is indirectly constrained
due to the axle that connects the tire to the car, and the bottom side of the tire is displaced by the ground. Here, we investigate the topology in stress tensors when the torus is fixed at the top symmetrically and is displaced at the bottom side symmetrically.

The material is highly incompressible.

2. Dimension
   verts:35616
   tets:26656 * 6 = 159,936

=================================================
neu_03_TorusVertical0p49 
(Neu fig. 11 (d)&(d))
------------------------------------------------
1. Setup

Same boundary conditions and mesh as what used in neu_02_TorusVertical0p1.

The material is highly compressible.

2. Dimension
   verts:35616
   tets:26656 * 6 = 159,936

=================================================
neu_04_TorusCamber_049 
(Neu fig. 11 (e)&(f))
------------------------------------------------
1. Setup

Same mesh as what used in neu_02_TorusVertical0p1.

Due to the required flexibility in joining the axles to the tires, there is a camber sometime that allows the tire to be tilted. 

The material is highly incompressible.

2. Dimension
   verts:35616
   tets:26656 * 6 = 159,936

=================================================
mode_01_ShockAbsorberComplex2_compress 
(mode fig. 1)
------------------------------------------------
1. Setup

a block under compression on center of the top side.

2. Dimension
   verts:91125
   tets:85184 * 6 = 511,104

=================================================
mode_02_Block_parabola 
(mode fig. 2 (a)&(b))
------------------------------------------------
1. Setup

Two spatially consecutive compressive loads which can be seen on highway bridges where fleets of heavy trucks are parked due to traffic lights or in structures where pairs of nuts and bolts pin down an evenly spaced number of locations.

2. Dimension
   verts:86961
   tets:80000 * 6 = 480,000


=================================================
mode_03_Block_sine 
(mode fig. 2 (c)&(d, fig. 3, fig. 9)
------------------------------------------------
1. Setup

One side of the block is pulled up and the other side is pushed down forming a dome and a dome-shaped dent, respectively. 

2. Dimension
   verts:81396
   tets:75000 * 6 = 450,000


=================================================
mode_04_Block_RBOT_FixLR_equConstraints 
(mode fig. 10)
------------------------------------------------
1. Setup

The compressive load is misaligned with the natural geometric orientation of the block due to the addition of a slanted slab on the top of the box. This slanted slab presses down on the block. At the bottom of the block, we also add a full-length layer with a more rigid material. 

2. Dimension
   verts:52955
   tets:47736 * 6 = 286,416


=================================================
mode_05_threeParaboloid 
(mode fig. 11)
------------------------------------------------
1. Setup

Three spatially consecutive compressive loads which can be seen on highway bridges where fleets of heavy trucks are parked due to traffic lights or in structures where pairs of nuts and bolts pin down an evenly spaced number of locations.

2. Dimension
   verts:69741
   tets: 64000 * 6 = 384,000


=================================================